Frame type push-pull electromagnet
Frame type push-pull electromagnet principle: This product, because it issealed, and the magnetic force are greater than the conventional frameproducts, plus product all four sides closed, so it can be effective dust, can be used in harsh environments.
All are through the solenoid electromagnet principle, made of copper wirewound into a coil, when the coil is energized, the coil produces a magnetic field, one side is the N pole, S pole is fixed iron core side, one side is apolarity, a movable slide rod side is a polarity, because of the attraction of the principle, produce magnetic field the iron core and the sliding rod pull together, because of the fixed iron core is fixed, so the movable slide barsuck, suck at the same time, the sliding rod can drive the object, so as to achieve the tension. The push-pull electromagnet, can be pushed or pulled,pull type is very simple structure, use the slider to pull, and push type, varyin structure, the fixed iron core in moving the movable sliding suction rod, amiddle hole fixed iron core, a movable front end of the slide bar is packed in a top rod, when the core suction sliding rod, a top rod slide bar in front of the gradually introduced, formed to promote the role of.
The composition of the 1 frame type push-pull electromagnet U1146structure:
Pull the main parts: shell, cover plate, coil, wire, brass, iron core, a sliding rod.
Push major components: housing, cover plate, coil, wire, brass, iron core, a sliding rod, a top rod, block.
From the above: push and pull component parts are not the same, will the top rod, block,
So the use of methods are not the same, one is the power of pulling one object is energized to drive objects.
The 2 frame type push-pull electromagnet U1146 dimensions:
Frame length: 46mm
Frame width: 38mm
Frame height: 38mm
The sliding rod diameter: 11mm
The top rod diameter: 3mm
Block diameter: 9mm
The above car parts: sliding rod, a top rod, block sizes can be temporary to set by the customer,
Includes a slide mounting hole rod, slot size.
As shown in the following image size chart:
The 3 frame type sliding electrical parameters of electromagnet U1146:
Voltage: can choose, can choose between 6-220V, the product itself usingelectricity as the DC, if the customer requires the use of communication,
You can add rectifier bridge on the product.
Power: the power products are related to electricity rate of products.Electrified rate refers to the ratio of the power on time and off time.
Electricity rate is generally divided into: 100%, 50%, 25%, 10%, electricityrate increases, the power is small,
And electricity rate is small, the more power is.
Because in the effective volume of products, can only make a certain power, do big power,
The product will not load, leading to burn.
And through the heating problem of rate related to product electric, push and pull the electromagnet to long time heating electricity is more serious,
So the power will be relatively small.
The following figure: This product power and electricity rate parameter:
Current: current = power / voltage. Therefore, in the condition of constant power,
The size of the current depends on the voltage used much in use to customers.
The voltage is greater, less current, customers in the selection of products,
We must consider the good product supply circuit for the load current is big enough.
As shown above, when the power is 55W, customers using DC24V when thecurrent reached 2.29A,
So the circuit load current must be greater than 2.29A
The 4 frame type push-pull electromagnet U1146 performance:
Travel: travel means mentioned above principle, the movable slide bar tothe distance between the fixed iron core.
Is a power, the sliding rod pull movement between the distance to the core,
The fault movement called the product size the size of the stroke.
The U1146 can travel between selectable from 1mm-15mm,
According to the customer need to use to drive the object moving distance set.
Strength: the strength is, the movable slide rod pull in to the inertial forcesof the fixed iron core,
Is the magnetic field generated after the fixed iron core on the sliding rodhas the big pulling force.
This power to multiple objects have much thrust is the strength of the product.
Force and stroke, a fixed core and a slide bar spaced farther, so less force,
Spaced closer, so the more strength.
At the same time, the power strength and product related, the same trip, the same product, the greater the power, the greater strength.
The push-pull electromagnet U1146 power can according to below can be drawn, each with a different power,
Different stroke forces are represented in the following figure:
Such as: power 55W, 5mm power stroke corresponding between 3000-3500, power on the appearance of 3250gf.
Response time of 5 frame type push-pull electromagnet U1146:
Response time refers to products: electricity, movable slide bars longresponse time of exercise, this time is the product.
The length of time and response and products related to the size of thepower stroke.
It took U1146 products travel 10mm, power 22W, the response time of 0.125 seconds,
It is a second movement back and forth 4.
L life 6 frame type push-pull electromagnet U1146 temperature:
Temperature is installed on the client organizations: products, in use process, product degree of fever,
Electronic products are products of temperature rise and power, electricityrate.
U1146 products, if the power in the 55W, electricity rate of 10%, the basicno temperature rise,
If the electricity rate of 100%, the power is 5.5W,
Product coil temperature reached 50 degrees Celsius appearance.
Life: refers to the number of times the actions of the product
